How To Measure Curtains For Windows On Rods

Measuring for pall rods sizes is simple if you keep the following guidelines in listen.

Some guidelines are adequately straightforward such as:

• Measure your window from casing to casing or frame to frame. Don't mix and lucifer otherwise you will end up with an uneven look. If information technology is required to mix and match measurements, please give u.s. a call or e-mail us so we tin walk through it together and figure out the best solution!

• Use a metallic tape measure. Other types such as cloth tin can give erroneous measures

• Tape all measurements to the nearest 1/16th of an inch

• E'er double, triple check your measurements! You don't want to end up in the same position every bit this little fella...

Other things to go on in heed are a bit subjective and hither are full general guidelines for you to work with:

WIDTH. When measuring for window widths, you lot are trying to derive the correct pall rod length while because how much you would like your curtains to carry on past the window opening.

For determining appropriate rod length, general industry rule of thumb is to add ~twenty% to the measured frame or casing width. Here is a tabular array to keep handy for determining rod lengths quickly:

The factor to consider when measuring the width is space needed for the stack. When your curtains are opened, they will gather on either terminate – this is what is referred to as the "stack or stack back". This is important, especially when dealing with small windows as you lot will want to betrayal as much of the window glass equally possible to give an illusion of a larger window.

As an case, if your window is 48 inches (iv feet) broad and your defunction split in the center. If the stack width of your chosen defunction is 10 inches on either side, it would result in 10 inches of window glass on either side being covered past the gathered drapery. In other words, a full 20 inches (or ~40%) of the 48 inches of window glass will be covered past the stack.  Non ideal!

Ideally, you volition want to have the stack pushed all the mode over and then that very trivial, if whatever, of the window glass is covered. To accomplish that, yous would need to make certain the curtain rod is at least 20 inches larger than the original window size of 48 inches, or 68 inches. This would result in all 48 inches of window drinking glass showing when curtains are fully opened. Nigh ideal!

Information technology is not necessary for your curtain to always articulate the window drinking glass; however, we recommend allowing at least 3 inches minimum on each side to allow the curtains to open completely! Let the sunlight through!

For most drapery, you should allow approximately one-third of the width of the window for the stack-dorsum. If the pall fabric is unusually bulky, you lot may need to add an extra inch or two. Heavier fabrics and wider windows require more of a stack-back than lighter-weight fabrics on narrow windows.

A skilful rule of thumb is to have the mantle rod extend three to iv inches from each side of the window frame. Using a pencil, make a small mark at the appropriate width on the wall. You may want to use a level to make sure the marks are straight.

Bookkeeping for Finials. Be certain to consider the extra space required for decorative finials as the rod dimensions will not include the boosted width added past each finial. Finials come in a wide range of sizes, from ane.5 inches to nine. If space is tight, you can always opt for an stop cap.

Meridian. Determining the appropriate height to hang your drapery rod is crucial to achieving a successful pall installation.

Mensurate the meridian of your window treatments from the desired point (flooring, window sill, etc.)

Measure out on each side of your window to ensure that the window hardware is straight. Use a pencil to make a small mark on the wall on each side of the window, at the right height.

You lot will desire to hang the drapery high plenty so it covers the top of the window by at least a few inches if possible. If you are using tab / tie top drapery panels or prune rings which volition lower your drape making it sit well below the rod, you will need to motility the rod upwards a few inches every bit an allowance for the deviation, thus ensuring the top of your window will non be visible through the 'gap' created by the tab / tie tiptop panels or the clip rings.

Draperies can likewise help create the illusion of a taller / higher ceiling. You tin achieve that by mounting your rod 8 to 10 inches in a higher place your window; or for a more dramatic effect, 2 – 3 inches below your ceiling line or just beneath your crown molding or trim.

We recommend a minimum of 4 inches above. By doing so, the drapery will draw the eye up, creating a visually vertical line that gives the illusion of a higher ceiling. This creates a deluxe look, and is also helpful when you want to emphasize existing high ceilings or want to draw attention to intricate architectural details in a room.

If yous are using ready-made draperies, check to see what lengths are available, and decide on the rod elevation co-ordinate to the advisable panel length for your ceiling height. Most set up-made mantle panels are available in a diverseness of lengths, ranging from 84 inches, 96 inches, 108 inches and 120 inches. This offers flexibility without requiring custom curtain panels.

CWF PRO TIPS: Things get circuitous when determining how high to install curtain rods.

From our professional person feel over the years, we have ascertained that most customers tend to initially want their rods hung too low. Once nosotros explicate the design and conceptual advantages of installing curtain rods college, nigh tend to agree and finish up much happier and satisfied with the overall look afterwards the completed installation.

A drapery rod becomes a focal point in one case it is installed, and if it is installed too low it will create an optical illusion of a lower ceiling thus bringing downward the height of the room. The movie above sums that up pretty well. A drapery rod installed higher makes the windows and room wait taller, grander. The center is tricked, creating the visual illusion of height.

You can continue reading onto how to measure out for and select curtain rod sizes and brackets or browse our extensive curated choice of mantle rods to dress your windows similar yous've always wanted.

Source: https://www.continentalwindowfashions.com/pages/how-to-measure-for-rods

Posted by: jonesmopine.blogspot.com

Share this post